Beginner Macramé Plant Hanger: Easy Guide
Your fingers are sticky with something suspicious. The kitchen table has vanished under a nest of cream-coloured string, and there’s a half-finished knot dangling from a hook on the cupboard door. That’s the honest picture of my first macramé plant hanger. I’d love to tell you it looked effortless. It didn’t. I pulled the whole thing apart twice, and the third attempt had three knots facing the wrong way. But here’s the thing — it still held a pot of ivy for two years, and I still felt a small jolt of pride every time I walked past it. That’s the deal with macramé. It forgives you. It teaches you patience. And it gives you something you can actually hang in a window.
Never tied a macramé knot in your life? Good. This project is a gentle place to start. One knot, repeated, and a handful of supplies you probably already own. You’ll finish in an afternoon with something useful and handmade. No expensive kit required. Just string, scissors, and a bit of patience.
Materials List
- 3mm or 4mm cotton macramé cord — about 40 metres total. Natural cotton is the classic choice, but you can also use cotton clothesline, thick jute twine, or even recycled t-shirt yarn for a chunkier look.
- A wooden or metal ring — roughly 4–6cm across. An old curtain ring, a keyring loop, or a shower curtain ring all work beautifully.
- A tape measure or ruler — eyeballing it is tempting. Don’t.
- Sharp scissors — blunt ones will fray your cord and make you grumpy.
- A small pot with a plant — something lightweight for your first try. A succulent or small pothos is ideal.
- A hook or doorknob to hang from while you work — this keeps tension even and saves your back.
- Optional: masking tape — handy for holding cord ends together while you tie.
One word on cord length. Cut longer than you think you need. Macramé eats cord faster than any beginner expects, and a too-short strand is the single most common reason a project stalls. If in doubt, add 20cm to every piece.

Step-by-Step
- Cut your cords. You’ll need 8 lengths of cord, each about 4 metres long. Yes, that’s a lot. Lay them out flat and measure carefully. Cut one, then use it as a template for the rest so they match.
- Attach the cords to the ring. Fold each cord in half and find its midpoint. Hold the folded loop behind the ring, pull the two loose ends through the loop, and tighten. This is called a lark’s head knot, and it’s the foundation of almost every macramé project. Repeat with all 8 cords so they hang evenly around the ring.
- Sort your working strands. You now have 16 hanging cord ends. Pair them up so you’re working with 8 groups of 2. The outer cord in each pair does the wrapping. The inner cord stays still. This is the setup for a square knot.
- Tie your first row of square knots. Take the left cord of a pair, cross it over the two middle cords and under the right cord. Then take the right cord, pass it over the tail of the left cord, under the two middle cords, and up through the loop. Pull snug. Now repeat in mirror image: right cord over the middles, left cord through. That’s one complete square knot.
- Work across the row. Tie a square knot with each of the 8 pairs, keeping them level with one another. Check your tension as you go — loose knots will sag, tight knots will buckle. Aim for snug and even.
- Leave a gap, then tie the next row. Skip about 4cm of bare cord below your first row, then tie another full row of square knots. This gap creates the open, airy look that makes macramé plant hangers so appealing.
- Repeat. Tie a third row, again leaving a 4cm gap. Three rows is plenty for a beginner hanger. Four looks lovely too, if you have the cord.
- Gather the ends. Below your last row, bring all the cords together into one bundle. Wrap a spare length of cord tightly around the bundle about 10cm from the bottom, winding several times, then tuck the end under itself and trim. This creates the neck of the hanger.
- Create the pot cradle. Divide your cords into four equal groups. Tie a knot in each group about 12cm down. These four knots form the base that cradles the pot.
- Trim and finish. Trim the loose ends to a length you like — anywhere from 5cm to 15cm. Fray them slightly with your fingers for a soft, boho finish, or leave them neat. Slip your pot into the cradle and hang it up.

Beginner Tips
Your first hanger will probably be a bit wonky. Mine was. Here’s how to keep the wonk to a minimum.
Don’t skip the measuring. Uneven cord lengths show up in the finished piece as a lopsided hanger. It’s annoying to measure 32 metres of cord. Do it anyway.
Keep your tension consistent. This is the skill that separates a tidy hanger from a messy one. Check after every row — hold the piece up and look at it straight on. If one side is tighter, adjust before you carry on.
Hang as you go. Working on a flat table makes the cords twist and tangle. Hang the ring from a hook or doorknob so gravity helps you.
Resist the urge to pull knots too tight. A square knot should sit snug against the cords, not strangle them. Over-tightened knots make the whole piece stiff.
Count your knots out loud. It sounds silly. It works. Losing your place in a row is the fastest way to end up with a lopsided hanger.
Here’s my slightly counter-intuitive opinion: your first attempt doesn’t need to be perfect, and you shouldn’t aim for perfect. Macramé is a handmade craft, and the small irregularities are what make it feel like yours. Chasing symmetry on attempt one usually leads to frustration and a half-finished project in a drawer. Finish it, hang it, and make the second one neater.
Creative Variation
Once you’ve nailed the basic hanger, add a spiral. Instead of tying each square knot straight down, tie every knot starting with the left cord crossing over first. Do this for a full row, and the next, and the next. The knots will naturally twist into a lovely spiral pattern that runs down the length of the hanger. It looks far more complicated than it is, and it’s a great way to make a second hanger feel like a completely different project. You can spiral the whole hanger or just one section for contrast. Try it with a two-tone cord, too — natural cotton paired with a dyed strand makes the spiral pop.
Troubleshooting
The hanger is lopsided. Usually this means one row was tied tighter than another. Undo back to the last even row and retie with more consistent tension. Yes, it’s tedious. It’s also the fastest fix.
The knots are slipping. Cotton cord has some natural stretch. If knots slide, tighten them by pulling both working cords firmly in opposite directions. If the cord is very smooth or synthetic, switch to natural cotton — it grips better.
You’ve run out of cord. This happens. You can splice in a new length by overlapping the ends and tying a tight knot, then trimming the tails close. It won’t be invisible, but it’ll hold.
The pot won’t sit level. Check that your four cradle knots are at the same height. Adjust one at a time until the pot sits straight.
The hanger feels floppy. Add a fourth row of square knots. More structure means more support, especially for heavier pots.
And if it all goes wrong? Untie it and start again. Cord is forgiving, and so is this craft. Nothing is ruined.
There’s something quietly satisfying about making a plant hanger with your own hands. It costs very little, takes an afternoon, and gives you a small daily reminder that you can make useful, beautiful things. Your first one might be a little wonky. Hang it anyway. Then make another, and watch how much neater your knots get. Ready to give it a go this weekend?